|
Product Details:
|
| Temperature: | -40℃~+100℃ | Inner Tube: | Nitrile |
|---|---|---|---|
| Type: | TWO BraidS Of High-tensile Steel Wire | Color: | Black |
| High Light: | high pressure hydraulic hose,hydraulic rubber hose |
||
SAE 100R2AT/2SN WIRE BRAID REINFORCEMENT HDYRAULIC HOSE PIPE
|
Part |
In |
Hose ID | Hose OD | Max.Working pressure | Min.Bend Radius |
Min..burstpressure |
Weight (ibs/foot) | ||||
| In | mm | psi | Mpa | In | mm | psi | Mpa | ||||
| GR2SN-03 | 3/16 | 4.8 | 0.484 | 12.3 | 6000 | 41.4 | 3.5 | 89 | 24000 | 165.5 | 0.2 |
| GR2SN-04 | 1/4 | 6.4 | 0.593 | 15.1 | 5800 | 40 | 4 | 102 | 23200 | 160 | 0.24 |
| GR2SN-05 | 5/16 | 8.0 | 0.649 | 16.5 | 5075 | 35 | 4.5 | 115 | 20300 | 140 | 0.29 |
| GR2SN-06 | 3/8 | 9.5 | 0.753 | 19.1 | 4800 | 33.1 | 5 | 127 | 19200 | 132.4 | 0.34 |
| GR2SN-08 | 1/2 | 12.7 | 0.875 | 22.2 | 4000 | 27.6 | 7 | 178 | 16000 | 110.3 | 0.43 |
| GR2SN-10 | 5/8 | 15.9 | 1 | 25.4 | 3630 | 25 | 8 | 203 | 14520 | 100.1 | 0.5 |
| GR2SN-12 | 3/4 | 19 | 1.157 | 29.4 | 3120 | 21.5 | 9.5 | 241 | 12480 | 88 | 0.61 |
| GR2SN-16 | 1 | 25.4 | 1.5 | 38.1 | 2400 | 16.5 | 12 | 305 | 9600 | 66.2 | 0.88 |
| GR2SN-20 | 11/4 | 31.8 | 1.877 | 47.1 | 1820 | 12.5 | 16.5 | 419 | 7280 | 50.2 | 0.2938 |
| GR2SN-24 | 11/2 | 38.1 | 2.129 | 54.1 | 1310 | 9 | 20 | 508 | 5240 | 36.1 | 1.6134 |
| GR2SN-32 | 2 | 50.8 | 2.627 | 66.7 | 1160 | 8 | 26 | 635 | 4640 | 32 | 1.9825 |
| Tube: | Nitrile |
| Reinforcement: | Two braids of high-tensile steel wire. |
| Cover: | Neoprene. |
| Temperature range: | - 40ºC to + 100ºC |
Appllcatlon: Medium Pressure Hydraulic Applications including mobile, Machine tool and Agricultural
Applications, Using Petroleum or Water Based Hydraulic Fluids
About Hydraulic hose
Hydraulic hose from the inner rubber layer, the reinforced layer and the outer rubber layer (Figure 7),
the inner rubber layer is in direct contact with the oil, so the requirements should not be fluid corrosion.
In the long-term working condition can leak in the enhancement layer. Under the action of can withstand
the pressure. Therefore, appropriate use of nitrile rubber, the rubber material, influence the main factors
and performance of the inner rubber layer thickness and hardness, permanent deformation. The great
influence of hardness and permanent deformation of the sealing performance. High hardness,
permanent deformation after compression, the sealing performance is better. In general is 70 ~ 85
hardness, compression permanent deformation of 50% is the best. The best thickness is 1.5 ~ 2.5mm,
too thick will increase its flow volume in buckling caused by excess glue, the joint core sleeve and hose
contact surface accumulation, reduce the circulation section; too thin will be withheld. At the same time
fracturing in inner layer The wall thickness uniformity is also very important. If the uneven thickness,
compression will cause a break, a pile of rubber. Important factors in the surface appear pit also affect
the quality of the performance.
Contact Person: Duoli
Tel: +8613586832949
